武汉莫诺转子货真价实「多图」 [螺耐斯)10e361c]"内容：定转子过早磨损Premature wear of fixed rotor定转子过早磨损主要是由于定转子的间隙过小引起的。The premature wear of the fixed rotor is mainly caused by the small gap between the fixed rotor and the rotor.油管与抽油杆柱磨损Oil pipe and rod string wear油管与抽油杆柱磨损的原因一是因为井斜抽油杆贴在油管壁上引起的，可以通过加抽油杆扶正器使抽油杆柱居中来减轻或消除，另一个原因是定转子不同心及转子的偏心运动造成的，在定子以上加一节内径较大的回转筒即可避免。Tubing and sucker rod wear reason is because the deviation of sucker rod attached to the tubing wall caused by heating, pumping rod centralizer make the rod center to reduce or eliminate, another reason is caused by the eccentric motion of the rotor and the rotor are not concentric, avoid a day the diameter of rotary cylinder in the stator can be larger than.
Ｂ、转子B, rotors转子的结构也非常简单，主体是钢制杆件，一般外涂耐磨耐蚀的铬合金材料。其作用是传递动力和写定子形成密封腔。The structure of the rotor is also very simple, the main body is steel rod, generally coated with abrasion resistant and corrosion resistant chromium alloy material. Its function is to transfer power and write the stator to form a seal cavity.Ｃ、回转筒C, rotary barrel回转筒也就是一根内径较大的油管或空心定子筒，接在定子的上部以给转子和抽油杆杆柱以较大的回旋空间，防止转子和抽油杆因偏心运动磨擦磨损油管。A rotary cylinder is also an oil tube or hollow stator barrel with larger inner diameter. It is connected to the upper part of the stator to provide larger swirl space for the rotor and sucker rod string, so as to prevent the rotor and sucker rod from attrition wear due to eccentric wear.
Ｄ、限位器D, limiting device限位器为一个底部带限位板和流通通道的短节，接在定子的尾部，其作用是施工作业时给转子限位以防止下入过头而失去作用和杆柱脱落时防止杆柱掉入井底。The limiting device is a short section with bottom limit plate and distribution channel, which is connected to the tail of the stator. Its function is to limit the rotor to the rotor during ctruction1, so as to prevent it from falling into the overhead and lose its function and prevent the rod from falling into the bottom when the rod string falls off.
由于吸液管道或者轴封的地方有泄漏会导致空气被吸入到单螺杆泵里面，这样单螺杆泵就会处于吸空气的状态，进口管道不能形成负压所以螺杆泵吸不上液体。处理方法是检查、修理管道，排除杂物，调整更换轴封。 单螺杆泵电机反转也会导致螺杆泵吸不上液体的现象出现，调整电机的极性接头就可以了。 抽吸的矿浆太干，或在半干状态下运转也是螺杆泵吸不上液体的原因，这种情况只能稀释或向进料口加入充足的矿浆。 输送的液体粘度太高也会导致螺杆泵吸不上液体，如果是液体粘度太高的问题只能降低螺杆泵的转速然后提高液体的温度后使其粘度降低或者改用立式螺杆泵。
以上信息由专业从事莫诺转子的螺耐斯于2024/4/23 9:25:39发布
转载请注明来源：http://wuhan.mf1288.com/lnshbsb-2740393903.html
上一条：武汉高纯液氧批发服务至上「中醇化科技」
下一条：格雷母线定位系统在线咨询 知仁测控科技有限公司
